Oricom Marine Radio UHF100 User Manual

UHF100  
UHF200  
Operating Instructions  
For UHF100 and UHF200 40 Channel UHF  
2-way Citizen Band Radio  
 
Table of contents  
Table of contents ..........................................................................3  
Safety Information and Warnings ..................................................4  
Controls and Connectors...............................................................5  
Installation..................................................................................10  
Operations..................................................................................14  
UHF channels and frequencies....................................................30  
Warranty information (Australia)..................................................33  
This unit complies with all relevant Australian  
and New Zealand approval requirements.  
3
 
Safety Information and Warnings  
Please read before installing or opearating Your  
Oricom Radio  
The operation of this radio in Australia and New Zealand is subject to conditions  
in the following licenses. In Australia the ACMA Radio communications (Citizen  
Band Radio Stations) and in New Zealand by MED General User Radio License  
for Citizen Band Radio and operation is subject to conditions contained in those  
licences.  
Safety Information and Warnings  
Potentially Explosive Atmospheres  
Turn your radio OFF when in any area with a potentially explosive  
atmosphere. Sparks in such areas could cause an explosion or fire  
resulting in injury or even death.  
WARNING  
NOTE: Areas with potentially explosive atmospheres are often, but  
not always clearly marked. They include fueling areas such as below  
deck on boats; fuel or chemical transfer or storage facilities; areas  
where the air contains chemicals or particles, such as grain, dust,  
or metal powders; and any other area where you would normally be  
advised to turn off your vehicle engine.  
Blasting Caps and Areas  
To avoid possible interference with blasting operations, turn your  
radio OFF near electrical blasting caps or in a “blasting area” or  
in areas posted: “Turn off two way radios.” Obey all signs and  
instructions.  
Electromagnetic Interference/Compatibility  
Nearly every electronic device is susceptible to electromagnetic  
interference (EMI). To avoid the possibility of electromagnetic  
interference and/or compatibility conflicts, turn off your radio in any  
location where posted notices instruct you to do so such as health  
care facilities.  
4
 
Controls and Connectors  
Box Contents  
UHF100  
1 x RF Radio  
1 x Mount bracket with mounting screw  
for Remote Head Unit  
1 x Microphone Hanger  
1 x User Guide  
1 x Remote Head Unit with 2m cable  
1 x UHF100 Standard Microphone  
1 x DC Power Cord with inline fuse  
1 x Mounting bracket with mounting  
screws for RF Radio  
UHF200  
1 x RF Radio  
1 x Microphone Hanger  
1 x 2m long Extention cable  
1 x Coupler for extention cable  
1 x User Guide  
1 x Controller Speaker Micrphone  
1 x DC Power Cord with inline fuse  
1 x Mounting bracket with mounting  
screws for RF Radio  
5
 
Controls and Connectors  
Front View Remote Head unit (UHF100)  
1
2
3
9
4
5
6
7
8
1. Microphone connector  
2. LCD Display  
6. Priority Channel On/Off, Key Lock  
On/Off, Alpha-numeric display  
7. ID setting, 5 tone SelCall, Quiet  
8. Monitor, TSQ On/Off, Menu  
9. External speaker Jack (3.5mm for  
optional 8 ohm speaker)  
3. Power On/Off, channel & Volume  
control  
4. Function button by short push &  
Duplex On/Off by long push  
5. Open Scan, Memory On/Off, Group  
Scan  
6
 
Controls and Connectors  
Rear View  
Rear view of Radio (UHF100 & 200)  
1. 3.5mm external jack for optional 8 ohm speaker  
2. Power Supply connection  
3. Antenna connection  
3
2
1
Standard Microphone (UHF100)  
1. Push To Talk (PTT) button  
2. Volume Up, Channel Up  
3. Volume Down, Channel Down  
4. Power On/off, Volume and channel selector  
3
4
2
1
7
 
Controls and Connectors  
Top view of Contoller Speaker Microphone (UHF200)  
1. Volume Down, Channel Down  
2. Volume Up, Channel Up  
3. Power On/Off  
CH  
200RX  
1
3
2
Front view of Contoller Speaker Microphone (UHF200)  
4. LCD Display  
5. Function button & Duplex On/Off  
6. Open Scan, Memory On/Off, Group Scan  
7. Priority Channel On/Off, Key Lock  
On/Off, Alpha-numeric display  
8. ID setting, 5 tone Selcal, Quiet  
9. Monitor, TSQ On/Off, Menu  
10. PTT Switch  
4
9
8
7
6
5
10  
8
 
Controls and Connectors  
LCD Icons & Indicators (UHF100 and UHF200)  
1
2
3
4
5
6
18  
7
8
9
16  
10  
11  
12 13  
17  
15  
14  
1. FUNCTION  
10. Open Scan  
11. Group Scan  
12. Selelctive call Sending_to  
13. Selective call Receiving from  
14. 38 CTCSS Tone On/Off  
15. DCS On/Off  
16. Channel number  
17. ALPHA/NUMERIC  
18. Call Alarm  
2. RX or TX Signal strength  
3. Transmitter Indicator  
4. Receiver Indicator  
5. Quiet mode  
6. Priority On/Off  
7. Monitor On/Off  
8. Memory On/Off  
9. Key Lock  
9
 
Installation  
INSTALLATION  
CAUTION  
When installing your radio in your vehicle, check that during installation you do  
not damage any wiring or vehicle components that may be hidden around the  
mounting position.  
If you are unsure about how to install your radio, we suggest for optimum  
performance you have your radio professionally installed by a UHF specialist or  
Auto electrician. When installing the radio, avoid mounting it close to heaters or  
air conditioners. Do not press the PTT or CALL button before installing the  
antenna.  
Screw the mounting bracket and the remote head bracket to firm surfaces.  
To install the Radio;  
1. Fix the radio bracket in a suitable location.  
2. Then fix the radio in the bracket using the thumb screws.  
Note  
The radio contains a built-in loud speaker, The radio can be installed ‘out of the  
way’ and an external speaker can be used as an alternative (not supplied).  
To mount the Remote Head (UHF100)  
The remote head is supplied with a slim mounting bracket and thumb screws.  
Its small size and light weight design allows it to be mounted in almost any  
convenient position accessible to the driver.  
10  
 
Installation  
1. Fix the mounting bracket in place by screwing through the slots in the  
bracket.  
2. Fix the remote head unit to the mounting bracket with the thumb screws  
provided.  
3. Connect the standard microphone to the remote head socket, and tighten up  
the thumb screw.  
Fitting the Controller Microphone Speaker (UHF200)  
The Remote Head uses an 8 pin telephone style plug and socket:  
1. Position the microphone plug so the plastic flap faces downwards, and press  
the plug into the socket until it ‘clicks’.  
2. Gently press the rubber boot into the hole surrounding the socket so that the  
slot around the boot fits neatly inside the rim of the entry hole.  
3. If required use the external cable (supplied) to allow the radio to be installed  
further from the Controller Speaker Microphone.  
11  
 
Installation  
Disconnecting the Remote Head/Speaker Controller Microphone  
It is recommended that the remote head be left permanently connected to the  
radio, but if it must be disconnected, proceed as follows:  
1. Lift the rubber boot and the lip of the raised area on the front panel.  
2. Ease the rubber boot out of the cable entry hole and slide it along the cable  
away from the front panel.  
3. Identify the plug locking lever, move the lever towards the plug body. At the  
same time gently pull the plug from the socket (see previous page).  
Controller Speaker Microphone; part number, CSPKMIC  
Standard Microphone; part number, MIC050  
These can be purchased from the dealer you purchased the radio from or  
directly from Oricom.  
DC Power Connection  
The Radio is designed for 13.8 Volt DC, negative earth installations only (i.e.  
where the negative battery terminal connects to the chassis of the vehicle).  
For installation on 24 volt systems an inverter (not supplied) will need to be  
used.  
There are two possible methods of installation.  
Over voltage protection  
The radio has a high voltage input detection system, to warn you if an  
overvoltage situation occurs.  
Eg.: If the power supply voltage exceeds 17volts DC, the channel display (LCD  
backlight) will flash in 3 different colors when the unit is turned on.  
In additon, when transmitting, the TX indicator will automatically select a low  
power output.  
If the overvoltage warning appears, you must switch your radio off and  
disconnect it from the power source, before locating the cause of the trouble.  
The power source must not exceed 30volts.  
12  
 
Installation  
Radio stays ON when the ignition is switched OFF  
Connect the radio's negative (black) lead to the vehicle chassis, or directly to the  
batteries negative terminal.  
Connect the radio's positive (red) lead via the 2 Amp fuse to the battery's  
positive terminal. Alternatively, the positive lead could be connected at the fuse  
box at a point that has +13.8 Volts continuously available (preferably the battery  
side of the ignition switch) via the 2 Amp fuse.  
Radio turns OFF with the ignition switch  
Connect the radio's negative (black) lead to the vehicle's chassis, or directly to  
the batteries negative terminal.  
The radio's positive (red) lead should connect to an accessory point in the  
vehicle's fuse box via the 2 Amp fuse.  
Antenna information  
The antenna (not supplied) is of critical importance, to maximize your output  
power and receiver senstivity.  
A poor quality antenna or one not designed for the specific frequency band  
you are using will give poor performance. You should purchase an antenna  
designed for the 477MHz frequency band.  
Antenna installation  
1. Connect the antenna to the rear antenna socket using a PL259 coaxial connector.  
2. To obtain maximum performance from the radio, select a high quality antenna  
and mount it in a good location. Do not press the PTT or CALL button  
before installing the antenna.  
Optional accessories  
If required you may install an external (8 ohm, max 5w power) speaker fitted  
with a 3.5mm plug (not supplied).  
There is a jack located on the rear of the radio and on the UHF100 there is an  
additional jack on the side of the remote head unit.  
13  
 
Operations  
Power on and off  
* Press and hold the PWR button on the UHF100 Remote Head or the UHF200  
microphone PWR button for 2 seconds.  
* The default channel is set at CH01.  
CH  
CH  
200RX  
200RX  
UHF100  
UHF200  
Volume control  
* The UHF100 has a rotary electric volume control. Adjust the volume by rotating  
the channel knob clock-wise or adjust the volume control by pressing the  
Volume Up or Volume Down buttons on the microphone.  
* The UHF200 has Volume Up or Volume Down buttons on the microphone.  
Adjust to the preferred volume level.  
CH  
CH  
200RX  
200RX  
Channel Selection  
* Briefly press the PWR button. Select the channel by rotating the channel knob  
clock wise or adjust the channel selection by pressing the Channel Up or  
Channel Down buttons on the microphone from 1 to 40.  
* The UHF200 has Channel Up or Channel Down buttons on the microphone.  
Briefly press the PWR button, this will allow you to select the preferred  
channel.  
14  
 
Operations  
CH  
CH  
200RX  
200RX  
blinking  
Tri Function buttons  
To use the primary function (F, SC, PRI, ID, MO) press the required button.  
To use the secondary function (DPX, MEM, LO, CAL, TSQ) press and hold the  
button for 2 seconds.  
To use the third function (OS/GS, ALPHA, QUIET, MENU), press F/DPX and  
press the required button.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
Transmitting  
NOTE: Before transmitting on any channel, listen to check the channel is not already  
in use.  
Transmitting  
Select the desired channel. Press the PTT button on the microphone and speak  
normally into the microphone. Hold it approx. 7cm from your mouth. Release the PTT  
button to end the transmission and listen for a reply.  
Transmitting range  
The talk range depends on the environment and terrain, it will be affected by  
concrete structures and heavy foliage.  
Optimal Range  
Outdoors Flat, open  
areas  
Medium Range  
Outdoors Buildings  
or trees Also near  
residential buildings  
Minimal Range Outdoors  
Dense foliage or  
mountains. Also inside  
some buildings  
15  
 
Operations  
Priority Channel  
To store a Priority Channel, press the PRI/LO button. The letter "P" will appear  
when the priority channel is set. The channel you selected as your Priority  
Channel will then be automatically monitored during the Group Scan.  
Note: You can only store one channel as your priority channel.  
To store a Priority Channel  
1. Select the required channel.  
2. Briefly press and hold the PRI/LO button a loud beep is heard. The letter "P"  
appears when the priority channel is set.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
CTCSS  
CTCSS (Continuous Tone Coded Squelch System)  
CTCSS uses a sub-audile tone to open and close the squelch on your radio. This  
will allow a number of users to share the same channel without disturbing one  
another.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
Monitoring the Channel  
Monitoring the channel is helpful as it allows you to listen for other CTCSS users  
not within your group.  
To monitor the channel  
Press the MO/TSQ button. If no signals are present, a hissing noise will indicate  
an empty channel.  
Press the MO/TSQ button again to restore to its previous setting.  
16  
 
Operations  
Selecting the Required CTCSS Tone  
To pre-select the CTCSS tone on your radio, please refer to the MENU settings  
on page 24.  
Enabling CTCSS on a Channel  
If a CTCSS tone has been selected, it can be enabled on individual channels.  
1. Rotate the Channel knob to select the required channel. The letters "CT" will  
appear.  
2. Press and hold the MO/TSQ button.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
You may activate CTCSS on as many channels as you wish except channel 5  
and 35 which are designated for emergency use.  
Disabling CTCSS on a Channel  
Repeat steps 1 and 2 above.  
Note: You will not be able to activate CTCSS if the CTCSS tone is set to ‘OFF’.  
SCANNING  
The radio SCAN function has the ability to allow programmable channels to be  
scanned for groups of users.  
Channels can be scanned (40 channels per 5 seconds). When a signal is found,  
scanning will stop at that channel to allow the signal to be heard, then resume  
scanning when the channel is clear again.  
Scan Groups  
The Radio features three scan modes - Open Scan, Group Scan and Memory  
Scan.  
Open Scan  
The Open Scan feature scans for activity on all 38 CB channels. Once a channel  
is located, scanning will pause then will allow the signal to be heard. As soon as  
the channel is clear for 5 seconds, scanning will continue automatically.  
17  
 
Operations  
Open Scan  
Group Scan  
With Group Scan the Radio scans for activity, but in addition, it also inserts your  
Priority Channel into the scan sequence.  
This means that your Priority Channel will be monitored regularly while scanning  
to ensure that no calls are missed. Any signals received on your Priority Channel  
will take precedence over any signals received on the other channels.  
GROUP OR PRIORITY SCAN  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
Allows you to monitor a Priority Channel while scanning other channels in the  
GS memory.  
Memory On/Off  
Push and hold the SC/MEM button for 2 seconds, "M" will appear above the  
selected channel. Press SC/MEM button to remove scan memory from the  
selected open scan mode.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
18  
 
Operations  
Selcall  
Selcall or Selective Calling is a function that allows you to selectively call another  
radio, using a unique ID number. Your radio has 10 programmable Selcall ID  
memories. The ID memories are displayed as "C0 to C9". Here you will program  
Selcall ID numbers of other radios.  
Your Radio’s Selcall Identification number is preset at "12345". You must  
change this number to your own unique five digit Selcall ID number.  
Selcall Identification Name  
In addition to the Selcall ID number, each Selcall ID can be named using a 5  
character ALPHA name. The ALPHA name is stored in memory along with the  
ID code. When an incoming Selcall is received and the Selcall matches one of  
those in your radio's memory. The name can be displayed instead of the Selcall  
ID number.  
Recalling Selcall Idents from Memory  
1. Press the ID/CAL button to select the CALL TO mode.  
2. To select the required Identity in memory locations 'C0' to 'C9'. Rotate the  
channel knob on the front display of the UHF100. And, for the UHF200 press  
the Channel Up and Channel Down buttons on the microphone.  
3. When the required Selcall Memory is displayed, press and hold the ID/CAL  
button to send TO.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
Displaying ALPHA Names  
To display the Selcall’s ALPHA Name You must have the radio’s ALPHA display  
mode selected.  
To select the ALPHA display mode briefly press the F/DPX button followed by  
the ALPHA button. ‘ALPHA’ or ‘NUMER’ will be displayed for 2 seconds below  
the channel display to indicate the selected mode.  
19  
 
Operations  
Entering, Editting and Storing a Selcall Name or ID number  
1. Briefly press the ID/CAL button. The CALL TO mode will be selected and the  
last-sent Selcall memory location will be displayed.  
2. Rotate the Channel knob to select the required Selcall memory (locations  
C0 to C9). If no ALPHA name or ID number has been programmed for that  
memory, the radio will display ‘- - - - -’ otherwise it will display the last  
ALPHA name or NUMERIC code programmed into that memory.  
3. With the required memory location displayed, enter the required ALPHA name  
or NUMERIC code as follows:  
(a) Press and hold the F/DPX button until the radio beeps. The right hand  
character will flash. Rotate the Channel knob to select the required letter  
or number in the flashing character position.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
The following characters are available:  
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z, 0 1 2 3 4 5 6 7 8 9 _ *-  
(b) Briefly press the F/DPX button again to select the next character position.  
(c) Repeat steps (a) and (b) to enter all 5 characters as required.  
(d) Now press and hold the F/DPX button for 2 seconds. Then the radio will  
beep when the name or number is stored.  
Repeat the proceedure to add ALPHA names or numbers to any other Selcall  
Idents stored in memory.  
To exit CAL-TO mode  
Briefly press the ID/CAL button. The radio will return to normal operation.  
Receiving Selcalls  
When the Radio receives an ID code that matches your Selcall ID, it will  
automatically transmit an alarm tone. The caller’s Selcall ID name or number will  
be displayed.  
20  
 
Operations  
To return the call  
Press F/DPX and hold the ID/CAL button for 2 seconds until the radio beeps.  
The callers Selcall Identity will be sent to the caller.  
Cancelling the Selcall Alert  
To cancel the alarm and talk on the channel, press the PTT button. The alarm  
will be cancelled and the channel will be open for normal communication.  
Group Calling  
The Group Calling function allows you to transmit an “ALERT” tone to all  
members of a group at the same time.  
To setup Group Calling you must arrange your group ID codes in a certain  
format.  
Example:  
If one group consists of 8 vehicles the Group ID codes are arranged as follows:  
1
2
8
12340  
12341  
12347  
3
7
12346  
12342  
Base Station  
1234A  
4
6
12345  
12343  
12344  
5
21  
 
Operations  
To call the group, program the Base radio Group ID code to 1234A. When you  
call the group, all of the above vehicles will receive the Group Calling Tone.  
Group call IDs can be stored in memory the same way as a Standard Selcall ID  
code, please refer to Entering, Editing and Storing a Selcall ID number at page  
20.  
10 Radios  
100 Radios  
Group ID  
Individual ID  
Group ID  
Individual ID  
1234  
1234  
1234  
1234  
0
1
2
3
123  
123  
123  
123  
00'  
01'  
02'  
03'  
UP TO  
UP TO  
1234  
9
123  
99'  
QUIET Mode (Q)  
Puts the receiver in the Q mode. When activated, the radio prevents any  
unwanted conversations in the channels from being heard unless the call is  
specifically directed to you and the Selective call ID required to open the Q mode  
condition has been received.  
Under this condition, the PTT button is temporarily disabled.  
If you wish to use the same Channel for normal communication, simply remove  
the Channel from Q mode.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
22  
 
Operations  
Setting up QUIET Mode  
To setup QUIET mode you must first ‘tag’ the channels that you want to stay  
quiet, then activate the QUIET mode. Once QUIET mode is activated, the  
channels you have tagged will remain quiet to all incoming signals unless your  
Selcall Ident is received. Channels not tagged will remain open to all signals and  
will operate normally.  
1) Select the channel you want to put in "Q" mode using the channel selector.  
2) Briefly press F/DPX and then Quiet button. A beep is heard and the Q icon  
appears on the LCD display.  
3) While in Q mode condition, when the radio receives a code matching your ID,  
it will perform the following opeartions.  
• Automatically responds to the caller by transmitting Acknowledge tones.  
• Informs you that a caller is on the channel by emitting CALL Alarm and  
displays FROM icon.  
Menu FUNCTIONS  
The MENU feature provides a convenient method of customizing some of the  
radio’s functions. The following Menu Options are available. Note that some  
items are only available on certain channels.  
To access the Menu functions  
1. Briefly press the F/DPX button, then the MENU button. The first Menu  
function is displayed.  
2. Briefly press the SC/MEM button to cycle through each available function.  
After the last function has been selected, the cycle returns to the beginning.  
3. Rotate the Channel knob to alter the parameters of the selected function.  
4. Briefly press F/DPX button and then press Menu button to exit and store any  
changes.  
23  
 
Operations  
Third functions MENU list  
* Use the channel knob to change the value of each setting.  
* Use the Scan button to select the next function.  
* If a button is not pressed within 8 seconds the Radio will automatically exit the  
menu mode.  
* Please see below menu modes.  
Control  
Functions  
STEP  
Display  
Default  
3
off  
7
SQ Level  
adjust  
CTCSS  
38 tone  
DCS  
OFF, CTCSS,  
DCS  
67Hz  
104ch  
1. Amber  
2. Red  
3. Green  
OFF  
MENU  
Back Light by  
3 COLOR  
1
KEY BEEP ON/  
OFF  
On  
Off  
ON  
2 minute and  
30 second  
On  
Off  
ON  
OF  
Busy channel  
lock  
On  
Off  
5 sec  
10 sec  
15 sec  
P5  
SCAN stop  
time control  
P5  
MENU  
On  
Off  
Roger beep  
ON  
24  
 
Operations  
SQL:  
The radio has 8 preset ( off - 7) squelch levels:  
off - SQ off (monitor on condition)  
1 - Max sensitivity (min squelch)  
7 - min sensitivity (max/tight squelch)  
CTCSS and DCS setting  
This feature allows you to receive signals only from callers who have selected  
the same CTCSS and DCS code.  
DCS is similar to CTCSS. It provides 104 extra, digitally coded, squelch codes  
that follow after the 38 CTCSS codes. CTCSS 1-38, followed by DCS 1-104.  
Back light 3 Color  
You can select from three color options for the LCD backlight.  
The three options are Amber, Red and Green.  
Key Beep On/Off  
The Beep tone emits a tone when you press any of the buttons on the  
Microphone (except PTT switch).  
ToT (Time of Timer)  
Australian and New Zealand standards require that if the PTT is pressed for more  
than 3 minutes the unit must stop transmitting. The radio is set to stop transmitting  
after 2 minutes and 30 seconds of continous transmission. "ToT - On" will appear  
in the display and beep sound to indicate that the ToT is activated.  
Scan stop control  
The scan resume time can be set as an optional pause of 5 (default), 10 of 15  
seconds.  
Roger Beep  
This function emits a beep on the communication party to infrom the  
transmission is finished.  
25  
 
Operations  
Duplex Operation  
General  
Your radio has a Repeater Access function to allow use of local Repeater stations (if  
available in your area). Repeaters are shared radio system installed by interested  
parties (clubs, local business etc.) that pick transmissions on specific channels  
and re-transmit (or repeat) the received signal to another channel.  
Repeater Station  
The Repeater Access function can be set (from channel 1 to 8) used by local  
repeater stations. When activated, your radio will receive the Repeater on its  
specific channel (all repeater outputs are on channel 1 to 8) but transmits to the  
repeater channel 31 through 38.  
e.g.  
CH01 on Duplex mode will receive on CH01 but transmit on CH31  
CH02 on Duplex mode will receive on CH01 but transmit on CH32.  
Simplex mode Transmit/reciever  
Frequency (MHz)  
476.425  
Duplex Mode transmit  
Frequency(MHz)  
477.175 CH31  
477.200 CH32  
477.225 CH33  
477.250 CH34  
477.275 CH35  
477.300 CH36  
477.325 CH37  
477.350 CH38  
CH and Number  
1
2
3
4
5
6
7
8
476.450  
476.475  
476.500  
476.525  
476.550  
476.575  
476.600  
26  
 
Operations  
If you transmit on CH01 duplex mode, you are actually transmitting on CH31 the  
repeater station down converts your signal and retransmits on CH01.  
Your UHF100 and UHF200 allows you to pre-select Duplex operation individually  
on each channel.  
Push and hold the F/DPX button for 2 seconds, "DPXON" should appear on the  
LCD.  
Push F/DPX button to toggle the Duplex function On and Off.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
when transmitting  
Key Lock  
Push and hold the PRI/LO button for 2 seconds to lock all buttons except for  
the buttons below.  
(volume up and down, Power On/Off, Monitor, F/DPX, Push to talk ).  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
27  
 
Operations  
200 Receive (RX) only Channels  
Manual Programming  
The UHF Radio has a wide band search feature which will allow you to search  
Frequencies ranging from 400-512MHz (in 12.5KHz steps). You may search the  
full range or you may search one of 4 smaller bands separately.  
Turn power on.  
Briefly press the F/DPX button and then the Power button to access frequency  
band range.  
* Display will show default frequency band range.  
Briefly press the power button, the frequency number should be blinking.  
* you may use the rotary channel switch to select which channel you want.  
(example;)  
* Press and hold the PRI/LO button for 2 seconds, "400" first digits should be blinking.  
* Rotary channel switch to select which 3 frequency digits you want.  
(example;)  
28  
 
Operations  
* press the PRI/LO button, next 2 digits will be blinking for the next frequency digits.  
* Rotary channel switch to select which 2 frequency digits you want.  
Briefly press the F/DPX button and Power button to exit.  
Automatic programming  
1. Press the PWR button to turn the radio on.  
2. Briefly press the F/DUP button and then the Power Button.  
* The default Band frequency range will be displayed.  
3. Briefly press the SC/MEM button (OS is displayed).  
4. Briefly press the power or channel knob (channel will flash).  
5. Turn the power or channel knob until you get to an open frequency.  
6. Auto scan will commence in 2 to 3 seconds.  
* You will need to repeat steps 4 and 5 until the required frequency has been  
located.  
7. To store the required frequency, briefly press the ID/CAL button.  
8. To exit; repeat step 2.  
Factory reset  
If the radio's display locks up or stops functioning properly, you might need to  
reset your UHF radio.  
Caution: this procedure clears all the information you have stored in your UHF  
radio.  
Before you reset your UHF radio, try turning it off and on again. If your UHF radio  
is still not functioning correctly you may need to reset the UHF radio!  
While holding the F/DPX button, turn the UHF radio on. INITI AL will be displayed  
for 1 to 2 seconds, the radio will then return to its original display.  
OS / GS  
ALPHA  
QUIET  
MENU  
F/ DPX  
SC / MEM  
PRI / LO  
ID / CAL  
MO / TSQ  
29  
 
UHF channels and frequencies  
Channel Frequency Table  
Radiocommunications (Citizen Band Radio Stations) Class  
Licence 2002  
No licence is required to own or operate this radio in Australia and New Zealand.  
The Radiocommunications (Citizen Band Radio Stations) Class Licence 2002  
contains the technical parameters, operating requirements, conditions of licence  
and relevant standards for Citizen Band (CB) radios. CB radios must comply with  
the class licence for their use to be authorised under the class licence.  
UHF channels and frequencies  
IMPORTANT NOTE: The operation of your UHF radio in Australia and New  
Zealand is subject to conditions in the following licenses:  
In Australia the ACMA Radio communications (Citizen Band Radio Stations) and  
in New Zealand by MED the General User Radio License for Citizen Band Radio.  
Channel  
Frequency (MHz)  
476.425  
476.450  
476.475  
476.500  
476.525  
476.550  
476.575  
476.600  
476.625  
476.650  
476.675  
476.700  
476.725  
476.750  
Usage  
Duplex RX/Simplex  
Duplex RX/Simplex  
Duplex RX/Simplex  
Duplex RX/Simplex  
Emergency  
1
2
3
4
5
6
Duplex RX/Simplex  
Duplex RX/Simplex  
Duplex RX/Simplex  
Simplex  
7
8
9
10  
11  
12  
13  
14  
Simplex  
Simplex (Calling channel)  
Simplex  
Simplex  
Simplex  
30  
 
UHF channels and frequencies  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
476.775  
476.800  
476.825  
476.850  
476.875  
476.900  
476.925  
476.950  
476.975  
477.000  
477.025  
477.050  
477.075  
477.100  
477.125  
477.150  
477.175  
477.200  
477.225  
477.250  
477.275  
477.300  
477.325  
477.350  
477.375  
477.400  
Simplex  
Simplex  
Simplex  
Simplex  
Simplex  
Simplex  
Simplex  
No Use  
No Use  
Simplex  
Simplex  
Simplex  
Simplex  
Simplex  
Simplex  
Simplex  
Duplex TX/Simplex  
Duplex TX/Simplex  
Duplex TX/Simplex  
Duplex TX/Simplex  
Emergency  
Duplex TX/Simplex  
Duplex TX/Simplex  
Duplex TX/Simplex  
Simplex  
Simplex  
Channel 5 and 35 (paired for Duplex repeaters) are reserved as emergency  
channels and should be used only in an emergency.  
CTCSS and DCS will not operate on these channels.  
31  
 
UHF channels and frequencies  
Channel 11 is a calling channel generally used to call others and channel 40 is  
the customary road vehicle channel.  
Once contact is established on the calling channel, both stations should move to  
another unused "SIMPLEX" channel to allow others to use the calling channel.  
Channel 22 and 23 are for Telemetry and Telecommand use, voice  
commnuications are not allowed on these channel by law.  
Channel 9 and above are the best choices for general use in Simplex mode.  
38 CTCSS CODE LIST  
CODE  
OFF  
1
Frequency(Hz)  
OFF  
CODE  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
Frequency(Hz)  
131.8  
136.5  
141.3  
146.2  
151.4  
156.7  
162.2  
167.9  
173.8  
179.9  
186.2  
192.8  
203.5  
210.7  
218.1  
225.7  
233.6  
241.8  
250.3  
67.0  
2
71.9  
3
74.4  
4
77.0  
5
79.7  
6
82.5  
7
85.4  
8
88.5  
9
91.5  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
94.8  
97.4  
100.0  
103.5  
107.2  
110.9  
114.8  
118.8  
123.0  
127.3  
32  
 
Warranty information (Australia)  
Oricom makes no other warranties or conditions, express or implied, including as to  
merchantability and fitness for a particular purpose, except as stated in this Warranty.  
Any implied warranties that may be imposed by law are limited in duration to the  
Warranty Period.  
Oricom warrants that the product is free from defects in materials or workmanship  
during the Warranty Period. This Warranty in no way affects your statutory warranty  
rights under the Trade Practices Act 1974 or any other similar legislation. This  
Warranty does not extend to any product from which the serial number has been  
removed, was purchased outside of Australia or that has been damaged or rendered  
defective:  
1. as a result of lightning, over voltage, accident, misuse, abuse or other external  
causes;  
2. the operation outside the normal use of the product;  
3. by the use of parts not manufactured or sold by Oricom; or  
4. by modification or service by anyone other than:  
(a) Oricom; or (b) an Oricom authorised service provider.  
The Warranty Period will be 36 months from the date of purchase of the product  
evidenced by your dated sales receipt. You are required to provide proof of purchase  
as a condition of receiving warranty services. You are entitled to a replacement or  
repair according to the terms and conditions of this document if your product is  
found to be faulty within the Warranty Period. This Warranty extends to the original  
purchaser only and is not transferable.  
Spare parts may be new or equivalent to new. Spare parts are warranted to be free  
from defects in material or workmanship for thirty (30) days or for the remainder  
of the Warranty Period of the Oricom branded product in which they are installed,  
whichever is longer.  
During the Warranty Period, Oricom will replace and where possible repair the  
defective product. All component parts removed under this Warranty become the  
property of Oricom.  
33  
 
Warranty information (Australia)  
In the unlikely event that your Oricom product has a recurring failure, Oricom, at its  
discretion, may elect to provide you with a replacement product of its choosing that  
is at least equivalent to your product in performance.  
Oricom does not warrant that the operation of the product will be uninterrupted  
or error free. Oricom is not responsible for damage that occurs as a result of your  
failure to follow the instructions that came with the product.  
These terms and conditions together with any specific terms and conditions  
contained in the user guide to the product purchased constitute the complete and  
exclusive agreement between you and Oricom regarding the product. No change to  
the conditions of this Warranty is valid unless it is made in writing and signed by an  
authorised representative of Oricom.  
Oricom is not liable for any damages caused by the product or the failure of the  
product to perform, including any lost profits or savings or special, incidental or  
consequential damages. Oricom is not liable for any claim made by a third party or  
made by you on behalf of a third party.  
This limitation of liability applies whether damages are sought, or a claim made,  
under this Warranty or as a tort claim (including negligence and strict product  
liability), a contract claim or any other claim. However, this limitation of liability will  
not apply to claims for personal injury.  
Nothing in this Warranty excludes, restricts or modifies any condition, warranty, right  
or remedy which pursuant to the Trade Practices Act 1974 applies to this Warranty  
and which may not be so excluded, restricted or modified. For warranties that cannot  
be excluded, restricted or modified, Oricom limits the remedies available to those  
specified in the relevant legislation.  
34  
 
 
Customer Support  
If you suspect your product is not functioning to specification,  
before making a warranty claim please use the following resources.  
- Email our customer support team on support@oricom.com.au  
- Contact Oricom Customer Support team on 1300 889 785 or  
02 4574 8888 (Monday to Friday 9am to 5pm EST)  
Please retain your purchase receipt and attach to the back page of  
this user guide.  
Customer Support  
Email: support@oricom.com.au  
Phone: 1300 889 785  
Australia  
Oricom International Pty Ltd  
Locked Bag 658  
South Windsor, NSW 2756  
Fax: (02) 4574 8898  
New Zealand  
Oricom Live Chat  
 

NEC Computer Monitor MD21GS 3MP User Manual
Nilfisk ALTO Vacuum Cleaner Drum Top Vacuum User Manual
Nokia Cell Phone N95 User Manual
OEM Systems Speaker System RS 82B User Manual
Onkyo Headphones IE FC300 User Manual
Optimus Stereo System 120 2180 User Manual
Oregon Scientific Camcorder ATC5K User Manual
Palsonic CRT Television 3435TS User Manual
Panasonic DVD Player DVD T2000 User Manual
Patton electronic Network Router 2158B User Manual